The baby hand footprint is non-toxic and is especially formulated to be much softer than clay. There is no baking involved. Component: 2 bags of dough, 1 frame and 1 roller. How to Create Your baby hand footprint in 4 Easy Steps: 1. Soften your clay before using to make it as easy as possible to press baby's hand or foot in. Be sure to have clean hands! 2. Roll out the clay on a piece of cling film using a rolling pin to no less than 1 cm thick. Roll out on a board or tray you can take to baby rather than bring baby to the clay. 3. Press baby's hand or foot into the clay using firm & even pressure. Make sure you have pushed each finger/toe into the clay as well as the full heel/palm. 4. Trim the clay to the shape required whilst it is still wet. Make sure it will fit into the frame. Leave the imprint to dry for at least 24 hours before sticking it onto the backboard of the frame. Standard: EN71, ASTM D4236

Baby rubber hand footprint: Easy to keep; It won't get crack after dries; It won't be broken when falls. Component: 80grams of rubber dough/bag, 1 bag/tin, 1 tin/color box. How to Create Your baby hand footprint in 4 Easy Steps: 1. Soften your clay before using to make it as easy as possible to press baby's hand or foot in. Be sure to have clean hands! 2. Roll out the clay on a piece of cling film using a rolling pin to no less than 1 cm thick. Roll out on a board or tray you can take to baby rather than bring baby to the clay. 3. Press baby's hand or foot into the clay using firm & even pressure. Make sure you have pushed each finger/toe into the clay as well as the full heel/palm. 4. Trim the clay to the shape required whilst it is still wet. Make sure it will fit into the frame. Leave the imprint to dry for at least 24 hours before sticking it onto the backboard of the frame. Standard: EN71, ASTM D4236

Baby rubber hand footprint: Easy to keep; It won't get crack after dries; It won't be broken when falls. Component: 100grams of rubber dough/bag, 1 bag/tin, 1 tin/color box. How to Create Your baby hand footprint in 4 Easy Steps: 1. Soften your clay before using to make it as easy as possible to press baby's hand or foot in. Be sure to have clean hands! 2. Roll out the clay on a piece of cling film using a rolling pin to no less than 1 cm thick. Roll out on a board or tray you can take to baby rather than bring baby to the clay. 3. Press baby's hand or foot into the clay using firm & even pressure. Make sure you have pushed each finger/toe into the clay as well as the full heel/palm. 4. Trim the clay to the shape required whilst it is still wet. Make sure it will fit into the frame. Leave the imprint to dry for at least 24 hours before sticking it onto the backboard of the frame.

Baby hand and footprint easily create keepsake handprints & footprints of a baby's hands and feet. It is non toxic, acid-free. Component: 1 bag of clone powder, 1bag of molding powder, 1 bag of gold paint, 1 bag of silver paint, 1 brush and 1 frame. All of our kits have easy step-by-step instructions. Here are the general steps: 1 - Mix 50g molding powder with 1.2 time volume water. Once the material turns from pink to white, insert the foot, hand or pairs of hands into the molding material. Within about 5 minutes after turning white (if using room temp water), the mold sets. 2 - Wiggle the foot or hand(s) out of the soft pudding material. 3 - Mix 50g molding powder with half volume water. Pour the molding mixture into the mold. Let it harden. 4 -After 2-5 hours, cut open the pudding material gently. Air it until it gets completely dry. Usually this needs 24 hours. Then paint the gold or silver paint with the brush. 5. -Put it in the wooden frame. Enjoy it.